Table of content
- One hub for methods, certification and the procedure that actually governs
- Methods by structure type
- Personnel certification, in brief
- Nadcap: accrediting the supplier, not the person
- The OEM manual governs, not the generic standard
- Composite inspection: where it still trips people up
- Recent developments
- Key takeaways
- FAQs
- References
- Further reading
One hub for methods, certification and the procedure that actually governs
Aerospace NDT is not one discipline but several, stitched together by a stricter set of rules than most other industries use: a different dominant method for a composite wing skin than for a titanium engine disc, a personnel certification scheme (NAS 410 or EN 4179) that most other industries don’t use at all, a supplier accreditation (Nadcap) layered on top of that, and — above all of it — the specific manufacturer’s procedure for the part in front of you, which usually outranks any generic standard.
This hub maps that structure: which methods dominate which structure type, how personnel certification and supplier accreditation differ and relate, why the OEM manual is the real governing document, and where composite inspection in particular still trips people up. Two companion articles go deeper on pieces of this: Electromagnetic Testing for ECT/ECA/RFT/ACFM technique detail, and ASTM E1417 Penetrant Line Process Control for fluorescent-penetrant process control. A further planned article covers NAS 410/EN 4179 certification in full depth; this hub summarizes only what you need to orient yourself.
Methods by structure type
Structure type | Dominant method(s) | Why |
|---|---|---|
Composite (wing skins, fuselage panels, control surfaces) | Ultrasonic testing (pulse-echo, through-transmission, phased array) — described as the workhorse of composites inspection; pulsed infrared thermography for porosity, disbonds, delamination and near-surface inclusions; shearography for defects revealed via phase-map imaging; tap testing for thin laminates (under ~0.12 in/3.05 mm) and sandwich skin-to-core disbonds | UT, thermography and shearography all read through the thickness of a layered, anisotropic material in ways surface methods cannot; tap testing is fast and needs no couplant but only works on thin sections |
Metallic airframe (skin panels, structural members, fasteners) | Eddy current (surface cracks, including through paint; conductivity and coating-thickness checks); fluorescent penetrant (surface-breaking flaws in nonporous metal); radiography (cracks, corrosion, internal damage, foreign objects); ultrasonic (thickness, crack detection, corrosion evaluation) | These are the metal-NDT fundamentals, applied to thin, fatigue-critical structure |
Engine components (blades, discs, casings) | Fluorescent penetrant (per AMS 2644/AMS 2647), eddy current, magnetic particle testing on ferromagnetic parts (crankshafts, connecting rods, mounts), borescope/remote visual inspection for in-situ checks without teardown | Engine parts combine fatigue-critical geometry with limited internal access — RVI and surface methods dominate over volumetric methods for routine maintenance |
This table is intentionally a map, not a technique manual — each method’s detail lives in its own method hub or in the composite-specific limits section below.
Personnel certification, in brief
Aerospace NDT personnel are usually certified under NAS410 (“NAS Certification & Qualification of Nondestructive Test Personnel,” published by the Aerospace Industries Association) in the US, or its European harmonized counterpart EN 4179 (“Aerospace series — Qualification and approval of personnel for non-destructive testing”). Both are employer-based schemes: the employer, acting through its own Responsible Level 3, certifies its personnel, under stricter training, experience and outside-examination requirements than general-industry schemes like SNT-TC-1A. This contrasts with ISO 9712, a third-party scheme in which an independent certification body certifies the individual, producing a credential that is portable between employers.
This is a summary, not the full picture — a dedicated companion article covers NAS 410 and EN 4179 certification (levels, hours, exams, how employer-based certification actually works) in depth, and a broader certification-guide article covers how NAS 410 relates to ISO 9712 and SNT-TC-1A across industries generally.
Nadcap: accrediting the supplier, not the person
Nadcap is an industry-managed accreditation program for aerospace special processes, including NDT, run by the Performance Review Institute (PRI) on behalf of a council of subscriber aerospace manufacturers. It replaces each OEM separately auditing its own suppliers with one standardized audit that multiple OEMs accept.
NDT accreditation is audited against the AC7114 family of audit criteria: a base/general NDT checklist (AC7114), a supplemental document (AC7114/S), and method-specific facility-survey checklists — AC7114/1 (penetrant), /2 (magnetic particle), /3 (ultrasonic), /4 (film radiography), /5 (eddy current), /7 (rotating-component ultrasonic), /9 (remote interpretation of radiographic images) and /10 (digital radiography).
The distinction that matters: Nadcap accredits a supplier’s NDT process, facility and quality system — the audited entity is the company and its documented procedures, equipment and controls. NAS 410/EN 4179 certify individual people. A Nadcap-accredited facility still has to employ NAS 410/EN 4179-certified personnel to actually perform the NDT — the two are complementary requirements, not substitutes for each other. (Boeing’s own supplier-facing Nadcap FAQ states explicitly that Nadcap “accredits the supplier’s special processes, not individual people” — confirming this distinction at the OEM level, alongside PRI’s own program description.)
For the practical side of preparing for a Nadcap audit — the month-by-month checklist — see OneStopNDT’s dedicated Nadcap audit prep guide.
The OEM manual governs, not the generic standard
Industry guidance on this point is consistent: the technician follows “the manufacturer’s NDT manual, ASTM standard, or in-house NDT manual” — in that order, with the manufacturer’s own manual cited first. Where no manual exists for a given inspection, a Level III, not a general technician, has to develop the procedure. Deviating from the written procedure, rather than any ambiguity in the method itself, is a common real-world mistake.
Composite inspection: where it still trips people up
- Tap testing is operator-dependent. Industry sources describe it as “an art” — it is fast and needs no couplant, but its scope is real: suited to thin laminates under about 0.12 in (3.05 mm) and skin-to-core disbonds in sandwich structures, not a universal composite-inspection method.
- Ultrasonic testing needs a coupling medium (water or glycerin), a practical field complication that doesn’t exist for most metal-NDT methods.
- Layup-specific calibration and attenuation behavior. Ultrasonic attenuation varies by composite layup, so reference standards and calibration blocks need to match a part’s actual layup. Thermography is also sensitive to ambient conditions.
Recent developments
- NAS410 Revision 6 was jointly released by AIA and Accuris in early December 2025 (sources vary between December 1 and December 4). The headline change is a new Appendix D, giving Level 2 personnel an additional points-based route to sit the initial Level 3 exam; exact point thresholds are not disclosed in public coverage.
- EN 4179:2026 replaced the prior edition (dated late 2021 at the ASD-STAN/CEN level, though national adoption dates vary slightly by country — Sweden’s SIS, for instance, lists its predecessor as a 2022 edition), confirmed as newly in force by multiple national standards bodies (Estonia, Sweden, Switzerland, Czech Republic). This is a separate update from NAS 410 Rev 6, not a simultaneous joint release — EN 4179:2026 reached publication in February–April 2026, a few months after NAS 410 Rev 6.
- Regulatory ADs continue to mandate specific methods. FAA AD 2025-02-03 (effective March 17, 2025) requires repetitive ultrasonic inspections of fuselage structural areas on certain Regional Jet Series 100/440 airplanes for cracking — a concrete, current example of a regulatory airworthiness directive naming a specific NDT method rather than leaving method selection open.
Key takeaways
- Method choice tracks structure type: ultrasonic/thermography/shearography/tap test dominate composites; eddy current/penetrant/radiography/ultrasonic dominate metallic airframe; penetrant/eddy current/magnetic particle/RVI dominate engine components.
- NAS 410 and EN 4179 are employer-based personnel certification schemes, distinct from ISO 9712’s third-party model.
- Nadcap (via PRI, audited against the AC7114 family) accredits a supplier’s NDT process and facility; it does not replace NAS 410/EN 4179 personnel certification — a facility needs both.
- The specific OEM maintenance manual, not a generic ASTM/ASME standard, is the procedure a technician actually has to follow for a given part.
- NAS 410 Revision 6 (Dec 2025) and EN 4179:2026 are both current; regulatory ADs (e.g., FAA AD 2025-02-03) continue to mandate specific NDT methods on specific aircraft types.
FAQs
Why doesn’t one NDT method cover all aerospace structures? Composite, metallic airframe and engine components fail differently and need to be seen differently — a layered composite needs a through-thickness method like ultrasonic or thermography, while a surface-breaking fatigue crack in metal is exactly what eddy current and penetrant are built for.
What’s the difference between NAS 410 and EN 4179? NAS 410 (US, AIA) and EN 4179 (Europe, harmonized) are both employer-based NDT personnel certification schemes with closely tracking requirements — the employer certifies its own people, under stricter rules than general-industry schemes.
Is Nadcap the same as NAS 410/EN 4179 certification? No. Nadcap accredits the supplier’s NDT process and facility; NAS 410/EN 4179 certify the individual technician. A Nadcap-accredited shop still needs certified people to do the work.
Can I just follow the ASTM or ASME standard for a part instead of the OEM manual? No — industry guidance consistently puts the manufacturer’s own NDT manual first, with ASTM/in-house manuals as secondary references, and deviating from the written procedure is a cited common mistake.
What’s the biggest practical limitation of tap testing on composites? It only works on thin laminates (under about 0.12 in/3.05 mm) and sandwich skin-to-core disbonds, and its result depends heavily on operator skill.
What changed in NAS 410 Revision 6? A new Appendix D gives Level 2 personnel an additional points-based route to sit the initial Level 3 exam, released jointly by AIA and Accuris in December 2025.
Do regulators still mandate specific NDT methods by airworthiness directive? Yes — FAA AD 2025-02-03 is a current example, requiring repetitive ultrasonic inspection of specific fuselage areas on certain Regional Jet airplanes.
Where do I go for NAS 410/EN 4179 depth, or a broader certification-scheme comparison? This hub only summarizes certification. A dedicated companion article covers NAS 410/EN 4179 in depth, and a separate certification guide compares NAS 410, ISO 9712 and SNT-TC-1A across industries.
References
- CompositesWorld, “NDI methods for composites” (overview of tap test, ultrasonic, thermography, shearography for composite aerospace structures).
- AviationPros, “Nondestructive Inspection: The Big Five.”
- GlobalSpec, NAS410 listing (“NAS Certification & Qualification of Nondestructive Test Personnel”); EE Journal / AIA–Accuris press release on NAS410 Revision 6 (released December 4, 2025).
- National standards body listings confirming EN 4179:2026 (“Aerospace series — Qualification and approval of personnel for non-destructive testing”) as the current edition, replacing the December 2021 edition — Estonia (EVS), Sweden (SIS), Switzerland (SNV), Czech Republic.
- Open Exam Prep, certification-programs study guide (NAS410/EN4179 vs. ISO 9712 scheme comparison).
- PRI (Performance Review Institute), official Nadcap program page.
- Omnex / GoAudits, AC7114 audit-criteria training and reference pages.
- AviationPros, “The How, When and Where of Nondestructive Testing” (OEM-manual-governs-the-work framing).
- EE Journal / AIA–Accuris, NAS410 Revision 6 press release, December 4, 2025 (Appendix D Level 3 points route).
- National standards body listings, EN 4179:2026 edition (see [4]).
- Federal Register / govinfo, FAA Airworthiness Directive 2025-02-03 (effective March 17, 2025; repetitive ultrasonic inspection, MHI RJ Aviation CL-600-2B19 fuselage structure).
- Boeing, supplier-facing Nadcap FAQ (boeingsuppliers.com) — confirms Nadcap “accredits the supplier’s special processes, not individual people.”
Further reading
- ASTM E1417 Penetrant Line Process Control — the process-control procedure behind fluorescent/visible penetrant inspection lines, including aerospace maintenance applications.
- Remote Visual Inspection: From Borescopes to Drones — RVI equipment categories relevant to engine and confined-structure inspection.
- How to Prepare for Your Nadcap Audit — existing OSNDT spoke article on Nadcap audit preparation.
- Related reading: NAS 410 and EN 4179 Certification Explained; NDT Certification Guide: ISO 9712, SNT-TC-1A and NAS 410.
- Inspecting Composite Aerostructures: Method Selection — method-selection detail for the composite aerostructures flagged in this hub.
- Industrial CT for Additive Manufacturing Parts — CT inspection detail for additively manufactured aerospace components.




There are no comments yet!